ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Seagate Backup, Version 5.1.2 Copyright Arcada Software, Inc. 1995. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ This file contains important technical information about your program. To print this file, type COPY README.TXT PRN at the DOS prompt. The following subjects are discussed: 1. Installation 2. Memory Requirements 3. Compatibility Test Failure 4. Installing Seagate Backup on a System with Stacker 5. The DOS Append Command 6. Hardware Compression Not Supported 7. Power Management Conflicts 8. Parallel Port Drive Configuration 9. IRQ Conflicts 10. Maximum Parallel Port Cable Length 11. Encrypted Backup Sets 12. Restoring Files with NetWare Delete Inhibit or Rename Inhibit Attributes 13. Backing Up Large Numbers of Files to AccuTrak Tapes 14. NetWare Server Information and AccuTrak Tapes 15. Verify Your First Backup 16. Using Irwin AccuTrak Tapes 17. ASPI SCSI Manager Requirements 18. Supported SCSI Controllers 19. Files Not Backed Up 20. Tape Format Incompatibilities 21. Performance Issues on QIC-3020 Parallel Port Tape Drives 22. Support for Tape Drives Using Hardware Compression 23. Controller Conflicts 24. Large Capacity Tapes 25. Windows 95 Support ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 1. Installation ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Seagate Backup for DOS will not install or operate correctly from a DOS box within Windows. It must be installed and operated directly from the DOS prompt. This program works best when both the BUFFERS and FILES statements in your CONFIG.SYS file are set to at least 30. This program must have a FILES setting of at least 10 and a BUFFERS setting of at least 15 to run efficiently. NOTE: If you are using other software that requires a lower buffers setting, you should manually adjust the buffers setting. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 2. Memory Requirements ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Seagate Backup for DOS requires at least 512K of free memory; however, this software runs faster if more memory is available. To check your free memory, type MEM at the MS-DOS prompt. To free memory, remove any TSRs before running Seagate Backup. See your system documentation for other methods. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 3. Compatibility Test Failure ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ The compatibility test consists of a small backup and compare, automatically performed by Seagate Backup to verify that reliable backups can be performed with your current configuration. The most common cause of compatibility test failure is DMA error. Therefore, when the compatibility test fails, Seagate Backup automatically resets the DMA (Direct Memory Access) to Low Speed. During installation, other factors may contribute to compatibility test failure. For this reason, the following procedure is recommended if the compatibility test fails during installation: 1. Complete the installation 2. Restart Seagate Backup 3. Choose Configure 4. Choose Configuration Tests 5. Set the Direct Memory Access to High Speed 6. Redo the compatibility test If the compatibility test fails again, follow the guidelines presented in the on-line help, available by pressing F1. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 4. Installing Seagate Backup on a System with Stacker ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you have Stacker software installed on your computer, you may not want to let Seagate Backup make changes to your AUTOEXEC.BAT file. Some versions of Stacker create their own AUTOEXEC.BAT file which should not be modified, and it is this file that Seagate Backup will find. You can tell if this is the case on your computer if, during Seagate Backup installation, the AUTOEXEC.BAT file that is displayed says "DO NOT MODIFY THIS FILE." In this case, you will need to find your original AUTOEXEC.BAT file and make the following changes: ù Add the Seagate Backup directory to your PATH statement. ù Add the command "SET QBACKUP=path_name" where path_name is the directory you want Seagate Backup to use for setup and catalog files ù If you want to load the Backup Scheduler each time you start your computer, add the command QSCHED as the last command in your AUTOEXEC.BAT file. For more information on loading the Backup Scheduler, see the help topic "Installing the Backup Scheduler TSR." ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 5. The DOS Append Command ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you use the DOS Append command with the /X or /X:ON option, when you perform a restore, some files may not be restored. This is because of the way DOS reports names of existing files when this command is in effect. It is highly recommended that you deactivate the Append /x command before performing restores. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 6. Hardware Compression Not Supported ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Seagate Backup for DOS, Version 5.1.2, does not support the hardware compression function found on some high-speed controller cards. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 7. Power Management Conflicts ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Some Desktop computer systems and laptops have power management systems that take a "snapshot" of RAM and store it on the hard drive when they power down. This may create a conflict if it occurs during a backup or restore or a tape formatting operation. When using Seagate Backup, it is recommended that you turn OFF all power management features. If you're using a laptop, avoid running power management features by using an outlet rather than batteries. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 8. Parallel Port Drive Configuration ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If your parallel port tape drive does not automatically configure, first ensure that the power to the drive is on. If it is, turn it off, then on, and try configuring it again. See below for more suggestions. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 9. IRQ Conflicts ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ You may experience a conflict in IRQ selection if you are configuring a parallel port tape drive on a system that includes a sound card. SoundBlaster cards and compatibles use a default IRQ of 7, which is also used by a printer port (LPT1). If this conflict occurs, you can: * Change your sound card's IRQ if possible. Some cards do not allow this change and some games may not work correctly. * Check your system documentation to see if your parallel port can be configured to use a different interrupt. Devices that may conflict with printer port interrupt: Sound Cards Scanner Cards Network Cards Bus Mice Other printer ports Other devices IRQ usage can be determined by using the Microsoft Diagnostics Program. Exit Windows and type MSD at the DOS prompt. Note that MSD cannot always diagnose printer port IRQ conflicts. Printing does not require a hardware interrupt and will function normally even if an interrupt conflict exists. Symptoms of an IRQ conflict include Seagate Backup not finding the tape controller and network problems when backing up to tape. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 10. Maximum Parallel Port Cable Length ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Your parallel port tape drive should be connected directly to your system's parallel port. If you use the pass-through connector on the drive to connect a second device such as a printer, the maximum cable length for both devices is approximately 10 feet (3 meters). If you have difficulty using your tape drive when a second device is connected to the pass-through connector, disconnect the second device and its cable while using the tape drive. If you experience data loss when using a printer connected to the pass-through connector, shorten the printer's cable if possible or disconnect the tape drive while printing. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 11. Encrypted Backup Sets ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Seagate Backup cannot restore backup sets encrypted by other backup programs. You must use the original software to restore them. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 12. Restoring Files with NetWare Delete Inhibit or Rename Inhibit Attributes ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ During a Restore, you cannot overwrite files which have the NetWare Delete Inhibit (D) or Rename Inhibit (R) attribute set. To restore these files, you must first manually remove the Delete Inhibit or Rename Inhibit attribute. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 13. Backing Up Large Numbers of Files to AccuTrak Tapes ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ When using AccuTrak tapes, backing up a very large number of files--approximately 30,000 to an 80MB tape or 45,000 to a 120MB tape--will result in an error. Divide the files into two or more backup sets and back up each set to its own tape. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 14. NetWare Server Information and AccuTrak Tapes ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Because of the proprietary format used by the tapes, NetWare bindery files, trustee information, and extended attributes cannot be backed up to AccuTrak tapes. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 15. Verify Your First Backup ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ When you make your first backup with Seagate Backup, it is highly recommended that you use the Read and Compare option. During the Compare phase, Seagate Backup compares each file on the tape with the original on your hard drive to ensure that they are identical. While comparing will increase the time of the backup, it will confirm that your computer system, tape drive, and Seagate Backup are working together correctly. If compare fails, run a hard disk utility program to determine whether the hard drive is free of errors and try the backup again. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 16. Using Irwin AccuTrak Tapes ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you are using a Conner SuperHornet Plus drive, you can read from and write to tapes using either the standard QIC format or the Irwin AccuTrak format. The type of format is automatically detected by the drive and no special action is needed. If you are using either a WangTek or Conner 3010/3020 drive, you can read from but not write to AccuTrak tapes. To read an Irwin tape, you must first rebuild a catalog for the tape. (Select Rebuild from the Catalog menu.) When the rebuilding process is complete, you can load and use the catalog to restore files from that tape. NOTE: You cannot format an AccuTrak tape with either type of drive. You must purchase preformatted tapes (3M DC2080 or DC2120 tapes using the Rhomat format). ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 17. ASPI SCSI Manager Requirements ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ An installed and configured ASPI Manager for the system SCSI controller is required for use of Seagate Backup with SCSI tape drives. Refer to your SCSI controller or system manual for availability of an ASPI manager for your controller. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 18. Supported SCSI Controllers ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ The following SCSI controller cards are supported by this software: Adaptec AHA-1542CF Adaptec AHA-1510 Adaptec AHA-1500 Adaptec AHA-1522A Adaptec AHA-1530P Adaptec AHA-1540B Adaptec AHA-1542B Adaptec AHA-1542C Adaptec AHA-1640 Adaptec AHA-2940 Adaptec AHA-2842A Adaptec AHA-2742AT Adaptec AHA-1510A Adaptec AHA-1742A BusLogic BT-747C BusLogic BT-747S BusLogic BT-545C BusLogic BT-445C DPT PM-2022/95 DPT PM-2122/95 DPT PM-2021/95 DPT PM-2012/95 Future Domain TMC-850MCD Future Domain TMC-1670 Future Domain MCS-600 Future Domain MCS-700 Future Domain TMC-850M Future Domain TMC-3260 Future Domain TMC-3260SVP Future Domain TMC-1610MCD Future Domain TMC-1680 Future Domain TMC-1670SVP Future Domain SCSI2GO (PCMCIA) ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 19. Files Not Backed Up ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Seagate Backup does not log or back up a number of files to avoid potential system conflicts if they are restored. Compressed Volume files: DBLSPACE.0?? DRVSPACE.0?? STACVOL.* Windows swap files: 386SPART.PAR WIN386.SWP NetWare System files: BACKOUT.TTS NET$SPL.QUE NET$MSG.SYS DIRSTAMP.SYS NET$OBJ.SYS* NET$PROP.SYS* NET$VAL.SYS* NET$BIND.SYS* NET$BVAL.SYS* SYS$LOG.ERR * These NetWare bindery files will be backed up or restored only if you are logged on to a server as Supervisor. See your User Guide for more information. Additionally, Seagate Backup will not back up a number of temporary files used by the program when these files are found in the program's directory. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 20. Tape Format Incompatibilities ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Seagate Backup cannot format AccuTrak tapes. If your drive supports AccuTrak tapes, you should purchase them preformatted. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 21. Performance Issues on QIC-3020 Parallel Port Tape Drives ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ If you have a QIC-3020 Parallel Port tape drive you may experience a performance limitation, especially on systems with unidirectional parallel ports. This combination may not transfer data from the tape drive to the system fast enough to allow the tape to run continuously, or "stream." However, if you reformat the tape using the QIC-3010 format, the tape will run at half the speed of a QIC-3020 and stream more of the time. This will result in faster net restore times and less wear on the tape drive, but will cut the tape's capacity in half. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 22. Support for Tape Drives Using Hardware Compression ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Some SCSI tape drives contain specialized hardware which performs compression significantly faster than that performed by software using the system processor. Because of this large performance gain, hardware compression is always used in preference to software compression on these drives. If a tape is used in a drive that does not support the identical hardware compression as the original drive, the backup sets will be unreadable. In order to be compatible, the backup must be made with compression disabled in the Settings Screen. NOTE: By default, this program uses hardware compression. If you do not want to use hardware compression, disable the hardware compression option. ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ 23. Controller Conflicts ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ The Promise 2300 EIDE VLB controller must run in fast mode (/f parameter) in order to work with floppy tape drives. 24. Large Capacity Tapes ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Some combinations of tape drives and cartridges have capacities of over 4.3 GB (gigabytes). This release of your backup software is not able to display numbers that large. When initializing a tape of that size or displaying its contents, the Space Available display may not be correct--the actual capacity or space available on the tape may be 4.3 GB more than the program displays. You can still access and use all available space on the tape. Only the Initialization or Tape Directory display is incorrect. This will be fixed in a future release of the software. 25. Windows 95 Support ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Seagate Backup 5.1.2 is not supported on the Windows 95 operating system. The backup software is not Windows 95 enabled and thus does not support the backup and restore of Windows 95 long file names or Registry information.