Configuring SLA Monitor

Use this procedure to configure SLA Monitor.

Procedure

From the navigation tree, double-click Serviceability.
In the Serviceability tree, click SLA Monitor.
In the SLA Monitor tab, configure the parameters as required..
On the toolbar, click Apply.

SLA Monitor tab field descriptions

Name

Description

Status

Enables or disables the SLA Monitor agent. The default is disabled.

enabled: enables the SLA Monitor agent
disabled: disables the SLA Monitor agent

If you disable the agent, it does not respond to discover packets from a server.

If you disable the agent because of resource concerns, consider changing the server configuration instead, to alter the test frequency or duration, or the number of targets.

ServerBypass

Enables or disables the server bypass mode. The default is disable.

enable: enables an agent to respond to agent-to-agent test requests regardless of the server registration status.
disable: restricts agent responses when the agent is not registered with an SLA Monitor server.

RefuseServerTests

Sets the attribute to determine whether the SLA Monitor agent will refuse test requests from the server.

allow: enables an agent to accept test requests from the server.
refuse: causes the agent to reject test requests from the server.

ConfiguredAgentToAgentPort

Specifies the UDP port utilized by the SLA Monitor agent for agent-agent communication. If the value is 0, the SLA Monitor agent will utilize a default port value for the base agent-agent UDP communication port.

ConfiguredAgentAddrType

Indicates IPv4–based communications.

ConfiguredAgentAddr

Specifies the agent IP address. The default value is 0.0.0.0, which cases the agent to use the switch/stack IP address.

ConfiguredAgentPort

Specifies the UDP port for agent-server communication. The agent receives discovery packets on this port. The default is port 50011.

The server must use the same port.

CliAvailable

Specifies whether SLA Monitor agent CLI is available or not available.

	Note
	This affects only the SLA Monitor CLI and not the standard platform CLI.

CliTimeout

Configures the CLI timeout value in seconds. The default is 60 seconds.

	Note
	This affects only the SLA Monitor CLI and not the standard platform CLI.

CliTimeoutMode

Configures whether the agent automatic CLI session timeout is enabled or disabled.

	Note
	This affects only the SLA Monitor CLI and not the standard platform CLI.

ConfiguredServerAddrType

Indicates IPv4–based communications.

ConfiguredServerAddr

Specifies the server IP address. If an IP address is specified, the agent is restricted to use this server IP address. The default is 0.0.0.0, which allows the agent to register with any server.

ConfiguredServerPort

Specifies the server port. The default is 0, which allows the agent to disregard the source port information in server traffic.

The server must use the same port.

ConfiguredAltServerAddrType

Indicates IPv4–based communications.

ConfiguredAltServerAddr

Specifies a secondary server IP address.

SupportApps

Indicates SLA Monitor supported applications. This is a read-only field.

AgentAddressType

Indicates IPv4–based communications. This is a read-only field.

AgentAddress

Indicates the agent IP address. This is a read-only field.

AgentPort

Indicates the agent port. This is a read-only field.

RegisteredWithServer

Indicates whether the agent is registered with a server. This is a read-only field.

RegisteredServerAddrType

Indicates IPv4–based communications. This is a read-only field.

RegisteredServerAddr

Indicates the IP address of the SLA Monitor server with which the agent is registered .This is a read-only field.

RegisteredServerPort

Indicates the server TCP registration port . This is a read-only field.

RegistrationTime

Indicates the time in seconds since the agent registered with the server. This is a read-only field.

AgentToAgentPort

Indicates the base UDP port currently used by the SLA Monitor agent for agent-agent communication. The base UDP port is used to derive multiple agent communication ports. This is a read-only field.

EncryptionSupport

Indicates whether encrypted agent-server communication is supported by the agent. Secure images utilize encryption while non-secure images do not. This is a read-only field.